A privacy screen turns an open chain link fence into a private backyard, pool area or dog run. Installing one takes only simple tools and, for long runs, a helper. The secret is the order you tie it: top first, then pull it tight, then the ends and the bottom.
Quick answer
- Measure the fence height and the length of every run.
- Choose a screen the same height as the fence or slightly shorter.
- Zip-tie the top corners, then the top edge, pulling the screen tight as you go.
- Tie the end edges, then the bottom edge.
- Trim the zip tie tails and check the screen again after the first windy day.
What you need
- A privacy screen for each run of fence
- Zip ties (included with our standard screens)
- Flush cutters or scissors to trim the tails
- Work gloves and a tape measure
- A helper makes long runs much easier
Step 1: Measure the fence
Measure the height from the top rail down to where you want the screen to stop, and add up the length of each straight run between corner posts. Our screens come in 3, 4, 5, 6 and 8 ft heights in lengths up to 50 ft, and you can order a custom size for odd lengths.
Standard screens are made about 1 in. shorter than the listed size so they pull tight on the fence. Heavy Duty PLUS screens are made about 3 in. shorter than the listed height so they sit neatly on a fence of that height.
Step 2: Start at a corner post
Unroll the screen along the outside or inside of the fence, wherever you want the finished side to face. At one end, zip-tie the top corner grommet to the fence near the corner post, through the chain link and around the top rail if you can.
Step 3: Tie the top edge and pull it tight
Work along the top edge, putting a zip tie through each grommet. Pull the screen along the fence as you go so there are no sags. On our standard screens the grommets are every 24 in. along the long edges, with extra grommets at each corner.
Step 4: Tie the far end, then the bottom
At the far end, pull the screen tight and tie the top corner, then work down the end edge. Standard screens have grommets every 12 in. on the short edges. Finish with the bottom edge, tying every grommet. Tight is good, but do not pull so hard that the grommets distort.
Step 5: Join two screens
For a run longer than one screen, butt the second screen up against the first and tie both end edges to the same section of fence, so there is no gap. You can also overlap them slightly for a fully closed look.
Step 6: Trim and check
Snip the zip tie tails flush. After the first windy day, walk the fence and replace any tie that has slipped.
What about wind?
Our screens are knitted HDPE, so air passes through instead of hitting a solid wall. Still, any screen adds wind load to a fence. Use every grommet, and on open, windy sites such as pool barriers, sports courts and job sites, choose Heavy Duty PLUS. It uses heavier 220 GSM fabric, a 4 in. binding and grommets every 12 in. on the short sides and every 24 in. along the length.
Which screen should I choose?
| Standard | Heavy Duty PLUS | |
|---|---|---|
| Fabric | 170 GSM knitted HDPE | 220 GSM HDPE |
| Privacy | About 90% of the view blocked | Up to 98% of the view blocked |
| Heights | 3 to 8 ft, any custom length | 4, 5, 6 and 8 ft, 50 ft long |
| Warranty | 3 years | 4 years |
Ordering for a long fence? Add 3 or more screens to your cart and 10% comes off automatically at checkout. More help: how to choose a privacy fence screen and the privacy screen color guide.
Frequently asked questions
Does the screen go on the inside or outside of the fence?
Either works. Most people put it on the side they want to look at, so the zip ties and fence are on the other side.
Can I install a privacy screen on a pool fence or balcony?
Yes. Pool fences and railings usually need a 3 or 4 ft screen. See privacy screens for pool fences and the balcony privacy screen guide.
Are zip ties included?
Yes, our standard privacy fence screens come with cable zip ties.